From: Dave Taht <dave.taht@gmail.com>
To: Sebastian Moeller <moeller0@gmx.de>
Cc: Jonathan Morton <chromatix99@gmail.com>,
ECN-Sane <ecn-sane@lists.bufferbloat.net>,
bloat <bloat@lists.bufferbloat.net>
Subject: Re: [Bloat] [Ecn-sane] 2019-12-31 docsis strict priority dual queue patent granted
Date: Fri, 24 Jan 2020 00:59:42 -0800 [thread overview]
Message-ID: <CAA93jw5pnfM_TBgQFZyfk14+3UXUVLzR_umhwbFyt4a5ShzsSQ@mail.gmail.com> (raw)
In-Reply-To: <CAA93jw4+OiFCV2Z4gVpfP0oEMxo9xue_9kOc34y09_7RgdTLdA@mail.gmail.com>
To be deliberately contrarian - (I do try to only pay attention to
this a few days a month) - after also re-reading
https://www.cablelabs.com/technologies/low-latency-docsis and the
associated white papers (yes, 24 hours on a plane can do this to you)
1) I've never been able to figure out where the 99 percentile latency
figure so often cited came from. on the upstream which typically runs
well below 20Mbit, a single IW10 burst at 10Mbit is 1.3ms, so I've
generally figured it was either a long term figure, or calculated from
a much higher (100mbit? 1gbit?) downstream rate against some load
that's never been documented. (that I know of, please note that I
don't
read much of the traffic about this stuff)
2) There is a lot of valuable looking stuff in the lower level aspects
of the docsis LL standard. I'd noted it when I first read it, but
achieving .9ms baseline a/g latency finally does make it competitive
with fiber with whatever the heck "pgm" is. So far as I knew, the
overlapping grant request and estimator functions documented in the
patent are already present in most cablemodems already, and not really
tied to the ll spec... but that data would be interesting to get out
of the modem itself, somehow. The histogram is made available via a
MIB to the operator. It would be nice if those MIBs were also visible
to the user somehow.
3)
In the docsis-ll white paper and spec it lays out cmts requirements
also. With the cmtses currently exhibiting 500+ms of latency at
100Mbit loaded, from a mere "solving bufferbloat" perspective -
getting just pie there to work would be *marvelous* - it would be
superior to any of the fiber deployments I know of. dualpi, even if
not configured for l4s ecn support, would be a godsend. The ECO for
cablemodems at least, went out over a year ago.
some aqm tech becoming common on these head ends would also spur
deployment of aqm (or fq + aqm) tech on fiber also. But I've seen no
info as to what's going into cmtses today. Haven't seen any
announcements...
I still have no idea what is going to happen on 5G.
My initial experiments with the intel ax200 wifi card have been dismal.
On Fri, Jan 24, 2020 at 12:24 AM Dave Taht <dave.taht@gmail.com> wrote:
>
> Jeeze, you guys are up early. I read this stuff on the plane home from
> australia, and am still a bit under the weather.
>
> On Fri, Jan 24, 2020 at 12:01 AM Sebastian Moeller <moeller0@gmx.de> wrote:
> >
> > Hi Jonathan,
> >
> >
> > > On Jan 24, 2020, at 08:44, Jonathan Morton <chromatix99@gmail.com> wrote:
> > >
> > >> On 24 Jan, 2020, at 7:37 am, Dave Taht <dave.taht@gmail.com> wrote:
> > >>
> > >> "Otherwise, this exemplary embodiment enables system configuration to
> > >> discard the low-priority packet tail, and transmit the high-priority
> > >> packet instead, without waiting."
> > >
> > > So this really *is* a "fast lane" enabling technology. Just as we suspected.
>
> Well, there are weasel words elsewhere in the patent, and the dualq
> code for linux merely cleared a lane for L4S traffic and hardcoded the
> ect(1) as an identifier. It would be good to have more data on
> rtt-fairness, and on CE reordering of rfc3168 ecn packets.
>
> I spent time dreaming up also all the ways "queue protection" could be
> used against the user. Given the rigor of the l4s spec required, and
> how one misbehaving application can screw it all up, I could see
> queue protection of unknown sources that can be squelched on demand
> being a desirable "feature". This can be used to stop "unauthorized"
> mac addresses from participating in this design as one example.
>
> I like the idea of queue protection - there is a lot of malicious
> traffic worth throttling - but without a reporting scheme to the user,
> nor a means for the user to set it up, and the mechanism under the
> sole control of the ISP - not so much.
>
> My other in-flight entertainment was cory doctorow's latest piece,
> which was so good I submitted it to slashdot. (
> https://arstechnica.com/gaming/2020/01/unauthorized-bread-a-near-future-tale-of-refugees-and-sinister-iot-appliances/
> )
>
>
> > They seem to be setting their customers up for a head-on collision with the European Union's net neutrality rules, according to which "special services/fast lanes" are permissible under the condition thay they are realized with completely dedicated addition bandwidth. Just looking at their patent diagram there is one common input path to the classifier. So either that fast lane is not going to be a paid for fast lane, or the ISPs rolling this out will be in hot water with the respective national regulators (at least in the EU). The one chance would be to give the end-user control over the classification engine, or if the strict priority path is only used for ISP originated VoIP traffic (I seem to recall there are weasel words in the EU rules that would allow that and ISPs are doing something like that already, and I agree that it is nice to be able to field an emergency call independent of access link load).
>
> Well, one country at a time. NN is currently quite dead in the USA,
> and only a change in regime might change that, and it's unclear if any
> of the candiates understand the issues. Certainly with twin subsidies
> being aimed at 5G and broadband deployment in pending legislation, I
> have no idea what will happen here next. I view 5G with fear, watching
> frontier file for bankruptcy, also... I really wish all the fiber
> being run for 5G was being run into the home instead.
>
>
> >
> > Best Regards
> > Sebastian
> >
> >
> > >
> > > - Jonathan Morton
> > > _______________________________________________
> > > Ecn-sane mailing list
> > > Ecn-sane@lists.bufferbloat.net
> > > https://lists.bufferbloat.net/listinfo/ecn-sane
> >
> --
> Make Music, Not War
>
> Dave Täht
> CTO, TekLibre, LLC
> http://www.teklibre.com
> Tel: 1-831-435-0729
--
Make Music, Not War
Dave Täht
CTO, TekLibre, LLC
http://www.teklibre.com
Tel: 1-831-435-0729
next prev parent reply other threads:[~2020-01-24 8:59 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-01-23 2:29 [Bloat] " Dave Taht
2020-01-23 8:21 ` [Bloat] [Ecn-sane] " Luca Muscariello
2020-01-24 5:37 ` Dave Taht
2020-01-24 7:44 ` Jonathan Morton
2020-01-24 8:01 ` Sebastian Moeller
2020-01-24 8:24 ` Dave Taht
2020-01-24 8:59 ` Dave Taht [this message]
2020-01-24 9:51 ` Toke Høiland-Jørgensen
2020-01-25 16:04 ` Dave Taht
2020-01-24 12:08 ` Sebastian Moeller
2020-01-25 16:21 ` Dave Taht
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
List information: https://lists.bufferbloat.net/postorius/lists/bloat.lists.bufferbloat.net/
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=CAA93jw5pnfM_TBgQFZyfk14+3UXUVLzR_umhwbFyt4a5ShzsSQ@mail.gmail.com \
--to=dave.taht@gmail.com \
--cc=bloat@lists.bufferbloat.net \
--cc=chromatix99@gmail.com \
--cc=ecn-sane@lists.bufferbloat.net \
--cc=moeller0@gmx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox