Re: [Cerowrt-devel] saner defaults for config/firewall

[Fred Stratton <fredstratton@imap.cc>]

[-- Attachment #1: Type: text/plain, Size: 2959 bytes --]

So much for memory

mtd -r erase rootfs_data

is the correct invocation.


On 24/02/14 10:18, Fred Stratton wrote:
> I suggest you read the cero wiki. This details the original design 
> decisions. On the router,
>
> ssh in, and use
>
> mtd -r erase fs_data
>
> to recover to defaults. See
>
> http://wiki.openwrt.org/doc/techref/mtd
>
> If you ever have used  BB daily builds, you can type this in your sleep.
>
>
>
>
> On 24/02/14 10:05, Vincent Frentzel wrote:
>>
>>
>>
>>             I could be totally out for lunch here, but shouldn't that
>>     be se00 (secure ethernet) instead of eth0.1? At least on
>>     3.10.28-14 neuter "ifconfig" nor /etc/config/network mentions
>>     eth0.1 at all. Could you post both of these (so the result of
>>     calling ifconfig on a terminal on the router and the content of
>>     /etc/config/network ;), I am sure you know what I meant, just
>>     dying to be verbose for the sake of people stumbling over the
>>     archive of the mailing list)
>>
>>
>>
>> Hi Sebastian,
>>
>> Understood. I will come back to you with the ifconfig.
>>
>> For info, I did try both se00 and eth0.1. The reason I stuck with 
>> eth0.1 was that barrier breaker usually uses eth0.1 for br-lan with 
>> vlan enabled (eth0.1 appears in Luci in cerowrt). So in cero I just 
>> reenabled the vlan and used a type "bridge" on the network section (I 
>> renamed this section se99 instead of se00).
>>
>> I then added se99 it to the "lan" zone of the firewall. In the 
>> wireless config I specified network as "se99" instead of sw10 and 
>> sw00. I confirmed that the setup was correct in the web interface 
>> where eth0.1 sw00 and sw10 appeared under the new bridged interface ( 
>> there was the nice icon with the iface in brackets).
>>
>> I went on to modify the dhcp config of se00 and changed se00 
>> occurences for se99 and commented out entries for sw10/sw00. --> this 
>> would give me dhcp running on my new bridge.
>>
>> After a dnsmasq restart dnsmasq.conf shows the dhcp ranges line with 
>> interface se99. (I was expecting to see br-se99 but maybe that file 
>> is alias aware, could be wrong here).
>>
>> After a network restart I lost connectivity on cable. Wireless was 
>> working.
>>
>> I played a tad more and eventually lost wifi as well and had to 
>> reflash the router via tftp/factory image (maybe there is a reset 
>> trick you could give me to avoid this step).
>>
>> Are you running cerowrt in bridge mode? If yes could you share your 
>> network/firewall/dhcp config? Is there another file I should have 
>> edited and missed?
>>
>> Cheers,
>> V
>>
>>
>> _______________________________________________
>> Cerowrt-devel mailing list
>> Cerowrt-devel@lists.bufferbloat.net
>> https://lists.bufferbloat.net/listinfo/cerowrt-devel
>
>
>
> _______________________________________________
> Cerowrt-devel mailing list
> Cerowrt-devel@lists.bufferbloat.net
> https://lists.bufferbloat.net/listinfo/cerowrt-devel


[-- Attachment #2: Type: text/html, Size: 5855 bytes --]