here is an atheros based device that looks pretty nice also ... http://en.comfast.com.cn/product/SmartRepeater/item-217.html On Sun, May 1, 2016 at 3:45 PM, Outback Dingo wrote: > So this i finally got this ZBT-WG3526 seems a decent little device Costs > $60 USD, did get around to building an OpenWRT image on it and flashed it > this morning. installed openvpn and luci web ui ... looks pretty good so > far, and havient had any issues with the latest OpenWRT trunk on it. Seems > everything is wortking quite nicely. > Status > System > Hostname OpenWrt > Model ZBT-WG3526 > Firmware Version OpenWrt Designated Driver r49274 / LuCI Master > (git-16.117.68571-313e325) > Kernel Version 4.4.7 > Local Time Sun May 1 05:12:20 2016 > Uptime 3h 32m 42s > Load Average 0.03, 0.02, 0.05 > Memory > Total Available > 479112 kB / 514464 kB (93%) > Free > 476044 kB / 514464 kB (92%) > Buffered > 3068 kB / 514464 kB (0%) >  > dmesg > [ 0.000000] Linux version 4.4.7 (dingo@localhost.localdomain) (gcc > version 5.3.0 (OpenWrt GCC 5.3.0 r49274) ) #3 SMP Sun May 1 01:08:55 UTC > 2016 > [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 > [ 0.000000] bootconsole [early0] enabled > [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) > [ 0.000000] MIPS: machine is ZBT-WG3526 > [ 0.000000] Determined physical RAM map: > [ 0.000000] memory: 1c000000 @ 00000000 (usable) > [ 0.000000] memory: 04000000 @ 20000000 (usable) > [ 0.000000] Initrd not found or empty - disabling initrd > [ 0.000000] Zone ranges: > [ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff] > [ 0.000000] HighMem [mem 0x0000000010000000-0x0000000023ffffff] > [ 0.000000] Movable zone start for each node > [ 0.000000] Early memory node ranges > [ 0.000000] node 0: [mem 0x0000000000000000-0x000000001bffffff] > [ 0.000000] node 0: [mem 0x0000000020000000-0x0000000023ffffff] > [ 0.000000] Initmem setup node 0 [mem > 0x0000000000000000-0x0000000023ffffff] > [ 0.000000] On node 0 totalpages: 131072 > [ 0.000000] free_area_init_node: node 0, pgdat 8044cfe0, node_mem_map > 81000000 > [ 0.000000] Normal zone: 512 pages used for memmap > [ 0.000000] Normal zone: 0 pages reserved > [ 0.000000] Normal zone: 65536 pages, LIFO batch:15 > [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15 > [ 0.000000] VPE topology {2,2} total 4 > [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 > bytes. > [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize > 32 bytes > [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. > [ 0.000000] PERCPU: Embedded 10 pages/cpu @8148d000 s8416 r8192 d24352 > u40960 > [ 0.000000] pcpu-alloc: s8416 r8192 d24352 u40960 alloc=10*4096 > [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 > [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. > Total pages: 130560 > [ 0.000000] Kernel command line: console=ttyS0,115200 > rootfstype=squashfs,jffs2 > [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) > [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 > bytes) > [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 > bytes) > [ 0.000000] Writing ErrCtl register=0004621a > [ 0.000000] Readback ErrCtl register=0004621a > [ 0.000000] Memory: 514232K/524288K available (3508K kernel code, 163K > rwdata, 820K rodata, 232K init, 248K bss, 10056K reserved, 0K cma-reserved, > 262144K highmem) > [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 > [ 0.000000] Hierarchical RCU implementation. > [ 0.000000] NR_IRQS:256 > [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: > 0xcaf478abb4, max_idle_ns: 440795247997 ns > [ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, > wraps every 21474836475000000ns > [ 0.060000] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688) > [ 0.070000] pid_max: default: 32768 minimum: 301 > [ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) > [ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 > bytes) > [ 0.080000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 > bytes. > [ 0.080000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize > 32 bytes > [ 0.080000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. > [ 0.090000] CPU1 revision is: 0001992f (MIPS 1004Kc) > [ 0.170000] Synchronize counters for CPU 1: done. > [ 0.170000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 > bytes. > [ 0.170000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize > 32 bytes > [ 0.170000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. > [ 0.170000] CPU2 revision is: 0001992f (MIPS 1004Kc) > [ 0.250000] Synchronize counters for CPU 2: done. > [ 0.250000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 > bytes. > [ 0.250000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize > 32 bytes > [ 0.250000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. > [ 0.250000] CPU3 revision is: 0001992f (MIPS 1004Kc) > [ 0.330000] Synchronize counters for CPU 3: done. > [ 0.330000] Brought up 4 CPUs > [ 0.340000] clocksource: jiffies: mask: 0xffffffff max_cycles: > 0xffffffff, max_idle_ns: 19112604462750000 ns > [ 0.350000] pinctrl core: initialized pinctrl subsystem > [ 0.350000] NET: Registered protocol family 16 > [ 0.360000] rt2880-pinmux pinctrl: try to register 61 pins ... > [ 0.360000] pinctrl core: registered pin 0 (io0) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 1 (io1) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 2 (io2) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 3 (io3) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 4 (io4) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 5 (io5) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 6 (io6) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 7 (io7) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 8 (io8) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 9 (io9) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 10 (io10) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 11 (io11) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 12 (io12) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 13 (io13) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 14 (io14) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 15 (io15) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 16 (io16) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 17 (io17) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 18 (io18) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 19 (io19) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 20 (io20) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 21 (io21) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 22 (io22) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 23 (io23) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 24 (io24) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 25 (io25) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 26 (io26) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 27 (io27) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 28 (io28) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 29 (io29) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 30 (io30) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 31 (io31) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 32 (io32) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 33 (io33) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 34 (io34) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 35 (io35) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 36 (io36) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 37 (io37) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 38 (io38) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 39 (io39) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 40 (io40) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 41 (io41) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 42 (io42) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 43 (io43) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 44 (io44) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 45 (io45) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 46 (io46) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 47 (io47) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 48 (io48) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 49 (io49) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 50 (io50) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 51 (io51) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 52 (io52) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 53 (io53) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 54 (io54) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 55 (io55) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 56 (io56) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 57 (io57) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 58 (io58) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 59 (io59) on rt2880-pinmux > [ 0.360000] pinctrl core: registered pin 60 (io60) on rt2880-pinmux > [ 0.360000] pinctrl core: add 5 pinctrl maps > [ 0.360000] rt2880-pinmux pinctrl: found group selector 5 for wdt > [ 0.360000] rt2880-pinmux pinctrl: found group selector 8 for rgmii2 > [ 0.360000] rt2880-pinmux pinctrl: invalid group "wdt rst" for function > "gpio" > [ 0.370000] rt2880-pinmux pinctrl: found group selector 4 for jtag > [ 0.370000] rt2880-pinmux pinctrl: found group selector 7 for mdio > [ 0.370000] rt2880-pinmux pinctrl: request pin 18 (io18) for pinctrl > [ 0.370000] rt2880-pinmux pinctrl: request pin 22 (io22) for pinctrl > [ 0.370000] rt2880-pinmux pinctrl: request pin 23 (io23) for pinctrl > [ 0.370000] rt2880-pinmux pinctrl: request pin 24 (io24) for pinctrl > [ 0.370000] rt2880-pinmux pinctrl: request pin 25 (io25) for pinctrl > [ 0.370000] rt2880-pinmux pinctrl: request pin 26 (io26) for pinctrl > [ 0.370000] rt2880-pinmux pinctrl: request pin 27 (io27) for pinctrl > [ 0.370000] rt2880-pinmux pinctrl: request pin 28 (io28) for pinctrl > [ 0.370000] rt2880-pinmux pinctrl: request pin 29 (io29) for pinctrl > [ 0.370000] rt2880-pinmux pinctrl: request pin 30 (io30) for pinctrl > [ 0.370000] rt2880-pinmux pinctrl: request pin 31 (io31) for pinctrl > [ 0.370000] rt2880-pinmux pinctrl: request pin 32 (io32) for pinctrl > [ 0.370000] rt2880-pinmux pinctrl: request pin 33 (io33) for pinctrl > [ 0.370000] rt2880-pinmux pinctrl: request pin 13 (io13) for pinctrl > [ 0.370000] rt2880-pinmux pinctrl: request pin 14 (io14) for pinctrl > [ 0.370000] rt2880-pinmux pinctrl: request pin 15 (io15) for pinctrl > [ 0.370000] rt2880-pinmux pinctrl: request pin 16 (io16) for pinctrl > [ 0.370000] rt2880-pinmux pinctrl: request pin 17 (io17) for pinctrl > [ 0.370000] rt2880-pinmux pinctrl: request pin 20 (io20) for pinctrl > [ 0.370000] rt2880-pinmux pinctrl: request pin 21 (io21) for pinctrl > [ 0.370000] rt2880-pinmux pinctrl: failed to lookup the sleep state > [ 0.370000] FPU Affinity set after 11720 emulations > [ 0.400000] pinctrl core: add 1 pinctrl maps > [ 0.400000] rt2880-pinmux pinctrl: found group selector 6 for pcie > [ 0.400000] rt2880-pinmux pinctrl: request pin 19 (io19) for > 1e140000.pcie > [ 0.400000] pull PCIe RST: RALINK_RSTCTRL = 0 > [ 0.700000] release PCIe RST: RALINK_RSTCTRL = 7000000 > [ 0.700000] ***** Xtal 40MHz ***** > [ 0.710000] release PCIe RST: RALINK_RSTCTRL = 7000000 > [ 0.710000] Port 0 N_FTS = 1b102800 > [ 0.710000] Port 1 N_FTS = 1b102800 > [ 0.720000] Port 2 N_FTS = 1b102800 > [ 1.870000] -> 21007f2 > [ 1.870000] PCIE0 enabled > [ 1.870000] PCIE1 enabled > [ 1.880000] PCIE2 enabled > [ 1.880000] PCI host bridge /pcie@1e140000 ranges: > [ 1.880000] MEM 0x0000000060000000..0x000000006fffffff > [ 1.890000] IO 0x000000001e160000..0x000000001e16ffff > [ 1.890000] PCI coherence region base: 0x60000000, mask/settings: > 0xf0000002 > [ 1.930000] mt7621_gpio 1e000600.gpio: registering 32 gpios > [ 1.930000] mt7621_gpio 1e000600.gpio: registering 32 gpios > [ 1.940000] mt7621_gpio 1e000600.gpio: registering 32 gpios > [ 1.940000] PCI host bridge to bus 0000:00 > [ 1.950000] pci_bus 0000:00: root bus resource [mem > 0x60000000-0x6fffffff] > [ 1.960000] pci_bus 0000:00: root bus resource [io 0xffffffff] > [ 1.960000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags > 0x0] > [ 1.970000] pci_bus 0000:00: No busn resource found for root bus, will > use [bus 00-ff] > [ 1.980000] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400 > [ 1.980000] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] > [ 1.980000] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff] > [ 1.980000] pci 0000:00:00.0: supports D1 > [ 1.980000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot > [ 1.980000] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400 > [ 1.980000] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff] > [ 1.980000] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff] > [ 1.980000] pci 0000:00:01.0: supports D1 > [ 1.980000] pci 0000:00:01.0: PME# supported from D0 D1 D3hot > [ 1.980000] pci 0000:00:02.0: [0e8d:0801] type 01 class 0x060400 > [ 1.980000] pci 0000:00:02.0: reg 0x10: [mem 0x00000000-0x7fffffff] > [ 1.980000] pci 0000:00:02.0: reg 0x14: [mem 0x00000000-0x0000ffff] > [ 1.980000] pci 0000:00:02.0: supports D1 > [ 1.980000] pci 0000:00:02.0: PME# supported from D0 D1 D3hot > [ 1.980000] pci 0000:00:00.0: bridge configuration invalid ([bus > 00-00]), reconfiguring > [ 1.980000] pci 0000:00:01.0: bridge configuration invalid ([bus > 00-00]), reconfiguring > [ 1.990000] pci 0000:00:02.0: bridge configuration invalid ([bus > 00-00]), reconfiguring > [ 2.000000] pci 0000:01:00.0: [14c3:7603] type 00 class 0x028000 > [ 2.000000] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff] > [ 2.000000] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold > [ 2.000000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 > [ 2.000000] pci 0000:02:00.0: [14c3:7662] type 00 class 0x028000 > [ 2.000000] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff > 64bit] > [ 2.000000] pci 0000:02:00.0: reg 0x30: [mem 0x00000000-0x0000ffff > pref] > [ 2.000000] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold > [ 2.000000] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 > [ 2.000000] pci 0000:03:00.0: [1b21:0612] type 00 class 0x010601 > [ 2.000000] pci 0000:03:00.0: reg 0x10: [io 0x0000-0x0007] > [ 2.000000] pci 0000:03:00.0: reg 0x14: [io 0x0000-0x0003] > [ 2.000000] pci 0000:03:00.0: reg 0x18: [io 0x0000-0x0007] > [ 2.000000] pci 0000:03:00.0: reg 0x1c: [io 0x0000-0x0003] > [ 2.000000] pci 0000:03:00.0: reg 0x20: [io 0x0000-0x001f] > [ 2.000000] pci 0000:03:00.0: reg 0x24: [mem 0x00000000-0x000001ff] > [ 2.000000] pci 0000:03:00.0: reg 0x30: [mem 0x00000000-0x0000ffff > pref] > [ 2.000000] pci_bus 0000:03: busn_res: [bus 03-ff] end is updated to 03 > [ 2.000000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 03 > [ 2.000000] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] > [ 2.010000] pci 0000:00:00.0: BAR 0: failed to assign [mem size > 0x80000000] > [ 2.020000] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000] > [ 2.020000] pci 0000:00:01.0: BAR 0: failed to assign [mem size > 0x80000000] > [ 2.030000] pci 0000:00:02.0: BAR 0: no space for [mem size 0x80000000] > [ 2.040000] pci 0000:00:02.0: BAR 0: failed to assign [mem size > 0x80000000] > [ 2.040000] pci 0000:00:00.0: BAR 8: assigned [mem > 0x60000000-0x600fffff] > [ 2.050000] pci 0000:00:01.0: BAR 8: assigned [mem > 0x60100000-0x601fffff] > [ 2.060000] pci 0000:00:01.0: BAR 9: assigned [mem > 0x60200000-0x602fffff pref] > [ 2.060000] pci 0000:00:02.0: BAR 8: assigned [mem > 0x60300000-0x603fffff] > [ 2.070000] pci 0000:00:02.0: BAR 9: assigned [mem > 0x60400000-0x604fffff pref] > [ 2.080000] pci 0000:00:00.0: BAR 1: assigned [mem > 0x60500000-0x6050ffff] > [ 2.080000] pci 0000:00:01.0: BAR 1: assigned [mem > 0x60510000-0x6051ffff] > [ 2.090000] pci 0000:00:02.0: BAR 1: assigned [mem > 0x60520000-0x6052ffff] > [ 2.100000] pci 0000:00:02.0: BAR 7: no space for [io size 0x1000] > [ 2.100000] pci 0000:00:02.0: BAR 7: failed to assign [io size 0x1000] > [ 2.110000] pci 0000:01:00.0: BAR 0: assigned [mem > 0x60000000-0x600fffff] > [ 2.120000] pci 0000:00:00.0: PCI bridge to [bus 01] > [ 2.120000] pci 0000:00:00.0: bridge window [mem > 0x60000000-0x600fffff] > [ 2.130000] pci 0000:02:00.0: BAR 0: assigned [mem > 0x60100000-0x601fffff 64bit] > [ 2.140000] pci 0000:02:00.0: BAR 6: assigned [mem > 0x60200000-0x6020ffff pref] > [ 2.140000] pci 0000:00:01.0: PCI bridge to [bus 02] > [ 2.150000] pci 0000:00:01.0: bridge window [mem > 0x60100000-0x601fffff] > [ 2.150000] pci 0000:00:01.0: bridge window [mem > 0x60200000-0x602fffff pref] > [ 2.160000] pci 0000:03:00.0: BAR 6: assigned [mem > 0x60400000-0x6040ffff pref] > [ 2.170000] pci 0000:03:00.0: BAR 5: assigned [mem > 0x60300000-0x603001ff] > [ 2.180000] pci 0000:03:00.0: BAR 4: no space for [io size 0x0020] > [ 2.180000] pci 0000:03:00.0: BAR 4: failed to assign [io size 0x0020] > [ 2.190000] pci 0000:03:00.0: BAR 0: no space for [io size 0x0008] > [ 2.190000] pci 0000:03:00.0: BAR 0: failed to assign [io size 0x0008] > [ 2.200000] pci 0000:03:00.0: BAR 2: no space for [io size 0x0008] > [ 2.210000] pci 0000:03:00.0: BAR 2: failed to assign [io size 0x0008] > [ 2.210000] pci 0000:03:00.0: BAR 1: no space for [io size 0x0004] > [ 2.220000] pci 0000:03:00.0: BAR 1: failed to assign [io size 0x0004] > [ 2.230000] pci 0000:03:00.0: BAR 3: no space for [io size 0x0004] > [ 2.230000] pci 0000:03:00.0: BAR 3: failed to assign [io size 0x0004] > [ 2.240000] pci 0000:00:02.0: PCI bridge to [bus 03] > [ 2.240000] pci 0000:00:02.0: bridge window [mem > 0x60300000-0x603fffff] > [ 2.250000] pci 0000:00:02.0: bridge window [mem > 0x60400000-0x604fffff pref] > [ 2.260000] BAR0 at slot 0 = 0 > [ 2.260000] bus=0x0, slot = 0x0 > [ 2.260000] BAR0 at slot 1 = 0 > [ 2.270000] bus=0x0, slot = 0x1 > [ 2.270000] BAR0 at slot 2 = 0 > [ 2.270000] bus=0x0, slot = 0x2 > [ 2.280000] bus=0x1, slot = 0x0, irq=0xff > [ 2.280000] bus=0x2, slot = 0x1, irq=0xff > [ 2.280000] bus=0x3, slot = 0x2, irq=0x0 > [ 2.290000] clocksource: Switched to clocksource GIC > [ 2.300000] NET: Registered protocol family 2 > [ 2.310000] TCP established hash table entries: 2048 (order: 1, 8192 > bytes) > [ 2.310000] TCP bind hash table entries: 2048 (order: 2, 16384 bytes) > [ 2.320000] TCP: Hash tables configured (established 2048 bind 2048) > [ 2.330000] UDP hash table entries: 256 (order: 1, 8192 bytes) > [ 2.330000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) > [ 2.340000] NET: Registered protocol family 1 > [ 2.340000] PCI: CLS 80 bytes, default 32 > [ 2.340000] alarmtimer alarmtimer: no of_node; not parsing pinctrl DT > [ 2.340000] futex hash table entries: 1024 (order: 3, 32768 bytes) > [ 2.360000] squashfs: version 4.0 (2009/01/31) Phillip Lougher > [ 2.360000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) > (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. > [ 2.370000] bounce: pool size: 64 pages > [ 2.380000] io scheduler noop registered > [ 2.380000] io scheduler deadline registered (default) > [ 2.390000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled > [ 2.400000] serial8250 serial8250: no of_node; not parsing pinctrl DT > [ 2.400000] console [ttyS0] disabled > [ 2.400000] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 33, > base_baud = 3125000) is a 16550A > [ 2.410000] console [ttyS0] enabled > [ 2.420000] bootconsole [early0] disabled > [ 2.420000] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys > error > [ 2.430000] pinctrl core: add 1 pinctrl maps > [ 2.430000] rt2880-pinmux pinctrl: found group selector 9 for spi > [ 2.430000] rt2880-pinmux pinctrl: request pin 34 (io34) for > 1e000b00.spi > [ 2.430000] rt2880-pinmux pinctrl: request pin 35 (io35) for > 1e000b00.spi > [ 2.430000] rt2880-pinmux pinctrl: request pin 36 (io36) for > 1e000b00.spi > [ 2.430000] rt2880-pinmux pinctrl: request pin 37 (io37) for > 1e000b00.spi > [ 2.430000] rt2880-pinmux pinctrl: request pin 38 (io38) for > 1e000b00.spi > [ 2.430000] rt2880-pinmux pinctrl: request pin 39 (io39) for > 1e000b00.spi > [ 2.430000] rt2880-pinmux pinctrl: request pin 40 (io40) for > 1e000b00.spi > [ 2.430000] spi-mt7621 1e000b00.spi: sys_freq: 50000000 > [ 2.440000] m25p80 spi32766.0: using chunked io (size=32) > [ 2.440000] m25p80 spi32766.0: w25q128 (16384 Kbytes) > [ 2.450000] 4 ofpart partitions found on MTD device spi32766.0 > [ 2.450000] Creating 4 MTD partitions on "spi32766.0": > [ 2.460000] 0x000000000000-0x000000030000 : "u-boot" > [ 2.470000] 0x000000030000-0x000000040000 : "u-boot-env" > [ 2.470000] 0x000000040000-0x000000050000 : "factory" > [ 2.480000] 0x000000050000-0x000001000000 : "firmware" > [ 2.510000] 2 uimage-fw partitions found on MTD device firmware > [ 2.520000] 0x000000050000-0x0000001c468e : "kernel" > [ 2.520000] 0x0000001c468e-0x000001000000 : "rootfs" > [ 2.530000] mtd: device 5 (rootfs) set to be root filesystem > [ 2.540000] 1 squashfs-split partitions found on MTD device rootfs > [ 2.540000] 0x0000004d0000-0x000001000000 : "rootfs_data" > [ 2.550000] netif_napi_add() called with weight 128 on device eth%d > [ 2.570000] libphy: mdio: probed > [ 2.580000] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver > [ 2.590000] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine > at 0xbe100000, irq 10 > [ 2.600000] mt7621_wdt 1e000100.wdt: Initialized > [ 2.600000] NET: Registered protocol family 10 > [ 2.610000] NET: Registered protocol family 17 > [ 2.620000] bridge: automatic filtering via arp/ip/ip6tables has been > deprecated. Update your scripts to load br_netfilter if you need this. > [ 2.630000] 8021q: 802.1Q VLAN Support v1.8 > [ 2.630000] hctosys: unable to open rtc device (rtc0) > [ 2.640000] UBIFS error (pid: 1): cannot open "ubi0:rootfs", error -19 > [ 2.650000] VFS: Mounted root (squashfs filesystem) readonly on device > 31:5. > [ 2.660000] Freeing unused kernel memory: 232K (80466000 - 804a0000) > [ 2.840000] random: nonblocking pool is initialized > [ 3.720000] init: Console is alive > [ 3.730000] init: - watchdog - > [ 4.470000] usbcore: registered new interface driver usbfs > [ 4.480000] usbcore: registered new interface driver hub > [ 4.480000] usbcore: registered new device driver usb > [ 4.500000] xhci-mtk 1e1c0000.xhci: xHCI Host Controller > [ 4.500000] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned > bus number 1 > [ 4.510000] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version > 0x96 quirks 0x00210010 > [ 4.520000] xhci-mtk 1e1c0000.xhci: irq 29, io mem 0x1e1c0000 > [ 4.530000] usb usb1: no of_node; not parsing pinctrl DT > [ 4.530000] hub 1-0:1.0: no of_node; not parsing pinctrl DT > [ 4.530000] hub 1-0:1.0: USB hub found > [ 4.530000] hub 1-0:1.0: 2 ports detected > [ 4.540000] xhci-mtk 1e1c0000.xhci: xHCI Host Controller > [ 4.540000] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned > bus number 2 > [ 4.550000] usb usb2: We don't know the algorithms for LPM for this > host, disabling LPM. > [ 4.560000] usb usb2: no of_node; not parsing pinctrl DT > [ 4.560000] hub 2-0:1.0: no of_node; not parsing pinctrl DT > [ 4.560000] hub 2-0:1.0: USB hub found > [ 4.560000] hub 2-0:1.0: 1 port detected > [ 4.580000] init: - preinit - > [ 8.120000] jffs2: notice: (383) jffs2_build_xattr_subsystem: complete > building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref > (0 dead, 0 orphan) fou > nd. > [ 8.140000] mount_root: switching to jffs2 overlay > [ 8.170000] procd: - early - > [ 8.180000] procd: - watchdog - > [ 8.820000] procd: - ubus - > [ 8.910000] procd: - init - > [ 9.480000] tun: Universal TUN/TAP device driver, 1.6 > [ 9.480000] tun: (C) 1999-2004 Max Krasnyansky > [ 9.490000] ip6_tables: (C) 2000-2006 Netfilter Core Team > [ 9.500000] Loading modules backported from Linux version > v4.4-rc5-1913-gc8fdf68 > [ 9.510000] Backport generated by backports.git > backports-20151218-0-g2f58d9d > [ 9.550000] mt76x2e 0000:02:00.0: ASIC revision: 76120044 > [ 9.580000] ROM patch already applied > [ 9.580000] Firmware Version: 0.0.00 > [ 9.580000] Build: 1 > [ 9.590000] Build Time: 201507311614____ > [ 9.610000] Firmware running! > [ 9.610000] ieee80211 phy0: Selected rate control algorithm > 'minstrel_ht' > [ 9.610000] mt7603e 0000:01:00.0: ASIC revision: 76030010 > [ 11.730000] mt7603e 0000:01:00.0: Firmware Version: _mt7603mp > [ 11.740000] mt7603e 0000:01:00.0: Build Time: 20151020155902 > [ 11.780000] firmware init done > [ 11.950000] ieee80211 phy1: Selected rate control algorithm > 'minstrel_ht' > [ 12.010000] ip_tables: (C) 2000-2006 Netfilter Core Team > [ 12.020000] nf_conntrack version 0.5.0 (8038 buckets, 32152 max) > [ 12.150000] xt_time: kernel timezone is -0000 > [ 12.160000] PPP generic driver version 2.4.2 > [ 12.160000] NET: Registered protocol family 24 > [ 16.310000] device eth0.1 entered promiscuous mode > [ 16.320000] device eth0 entered promiscuous mode > [ 16.330000] br-lan: port 1(eth0.1) entered forwarding state > > > > On Fri, Apr 29, 2016 at 6:49 AM, Outback Dingo > wrote: > >> my mt7621 AP arrived today, ill be checking it out, also note i found >> this.... >> >> https://mqmaker.com/ >> >> On Tue, Apr 26, 2016 at 6:48 AM, Outback Dingo >> wrote: >> >>> https://detail.1688.com/offer/1277654521.html >>> >>> same specs same device 330 RMB... i just ordered one.... >>> >>> On Tue, Apr 26, 2016 at 6:23 AM, Outback Dingo >>> wrote: >>> >>>> this is the same device >>>> http://www.zbtlink.com/products/router/ZBT-WG2926.html >>>> >>>> On Tue, Apr 26, 2016 at 6:13 AM, Outback Dingo >>>> wrote: >>>> >>>>> NO my wife says its 340 rmb... like less then 60 USD >>>>> >>>>> On Tue, Apr 26, 2016 at 6:02 AM, Dave Taht >>>>> wrote: >>>>> >>>>>> 340 bucks each, am I reading it right? >>>>>> >>>>>> as data sheets go, that's not bad (there are more in that dir), but >>>>>> what I wanted was the register sets for the wifi and cpu chips. >>>>>> >>>>>> On Mon, Apr 25, 2016 at 8:57 PM, Outback Dingo < >>>>>> outbackdingo@gmail.com> wrote: >>>>>> > router itself >>>>>> > >>>>>> http://cn.made-in-china.com/showroom/szzbtdz/product-detailUMVJbARKZCkv/ZBT-WG3526%E6%99%BA%E5%8D%9A%E9%80%9A%E9%AB%98%E7%AB%AF%E5%8F%8C%E9%A2%91%E5%A4%A7%E5%8A%9F%E7%8E%87%E6%99%BA%E8%83%BD%E6%97%A0%E7%BA%BF%E8%B7%AF%E7%94%B1%E5%99%A8%E5%AE%9A%E5%88%B6OEM.html >>>>>> > >>>>>> > chip set http://ftp.mqmaker.com/WiTi/Docs/Hardware/MT7621.pdf >>>>>> > >>>>>> > On Tue, Apr 26, 2016 at 4:38 AM, Dave Taht >>>>>> wrote: >>>>>> >> >>>>>> >> detailed documentation on the chipset would be nice... in any >>>>>> language.... >>>>>> >> >>>>>> >> On Mon, Apr 25, 2016 at 7:16 PM, Outback Dingo < >>>>>> outbackdingo@gmail.com> >>>>>> >> wrote: >>>>>> >> > guys, >>>>>> >> > >>>>>> >> > I am in china right now, i can probably source this in a day, >>>>>> let me >>>>>> >> > know if >>>>>> >> > you want me to get one for you and ill forward it, im going to >>>>>> try to >>>>>> >> > order >>>>>> >> > one today for myself >>>>>> >> > >>>>>> >> > On Tue, Apr 26, 2016 at 12:49 AM, Dave Taht >>>>>> wrote: >>>>>> >> >> >>>>>> >> >> Please send 1 mediatek router (and pcie card when you get 'em) >>>>>> to: >>>>>> >> >> >>>>>> >> >> Dave Taht & Lorna Reed >>>>>> >> >> 225 11th Ave apt 302 >>>>>> >> >> San Francisco, Ca, 94118-2167 >>>>>> >> >> >>>>>> >> >> I don't think I have time for the usb version. >>>>>> >> >> >>>>>> >> >> I am standardizing on this for my upcoming work. It's pretty >>>>>> darn >>>>>> >> >> libre, perhaps you could become a reseller of this also.... >>>>>> >> >> >>>>>> >> >> http://pcengines.ch/apu2c4.htm >>>>>> >> >> >>>>>> >> >> On Mon, Apr 25, 2016 at 3:43 PM, Christopher Waid >>>>>> >> >> wrote: >>>>>> >> >> > On 2016-04-25 06:37 PM, Dave Taht wrote: >>>>>> >> >> >> >>>>>> >> >> >> >>>>>> >> >> >> >>>>>> >> >> >> >>>>>> >> >> >> >>>>>> https://www.linkedin.com/pulse/mt7621-openwrt-dual-band-5-gigabit-port-router-support-anna-lee >>>>>> >> >> >> >>>>>> >> >> >> chris, you get anything in worth hacking on yet? >>>>>> >> >> > >>>>>> >> >> > >>>>>> >> >> > Yes- I think so. Didn't I send an email about this already? I >>>>>> don't >>>>>> >> >> > think >>>>>> >> >> > anyone responded though. Or maybe I failed to read the >>>>>> responses. I >>>>>> >> >> > asked if >>>>>> >> >> > anybody would like me to send them a mediatek chipset based >>>>>> router >>>>>> >> >> > board. If >>>>>> >> >> > people did email me please let me know again who you are. I >>>>>> know we >>>>>> >> >> > didn't >>>>>> >> >> > send out any of the router boards. I got 5 of them I believe. >>>>>> >> >> > >>>>>> >> >> > I'm currently flying back from the [GNU]LinuxFest North West >>>>>> event... >>>>>> >> >> > but if >>>>>> >> >> > people provide me addresses I can send out some sample router >>>>>> boards >>>>>> >> >> > to >>>>>> >> >> > start playing with. >>>>>> >> >> > >>>>>> >> >> > I also got some USB mediatek chipset based wifi dongles in as >>>>>> well I >>>>>> >> >> > believe. I forget how many of these I got. I also am brining >>>>>> in some >>>>>> >> >> > PCIE >>>>>> >> >> > mediatek cards theoretically although I'm unsure if we're >>>>>> actually >>>>>> >> >> > getting >>>>>> >> >> > our hands on these. I think the orders might have been >>>>>> canceled or >>>>>> >> >> > something- or maybe I just didn't follow up on checking the >>>>>> goods >>>>>> >> >> > shipped. >>>>>> >> >> >>>>>> >> >> >>>>>> >> >> >>>>>> >> >> -- >>>>>> >> >> Dave Täht >>>>>> >> >> Let's go make home routers and wifi faster! With better >>>>>> software! >>>>>> >> >> http://blog.cerowrt.org >>>>>> >> >> _______________________________________________ >>>>>> >> >> Cerowrt-devel mailing list >>>>>> >> >> Cerowrt-devel@lists.bufferbloat.net >>>>>> >> >> https://lists.bufferbloat.net/listinfo/cerowrt-devel >>>>>> >> > >>>>>> >> > >>>>>> >> >>>>>> >> >>>>>> >> >>>>>> >> -- >>>>>> >> Dave Täht >>>>>> >> Let's go make home routers and wifi faster! With better software! >>>>>> >> http://blog.cerowrt.org >>>>>> > >>>>>> > >>>>>> >>>>>> >>>>>> >>>>>> -- >>>>>> Dave Täht >>>>>> Let's go make home routers and wifi faster! With better software! >>>>>> http://blog.cerowrt.org >>>>>> >>>>> >>>>> >>>> >>> >> >