Yes, but you can't connect an openwrt flashed unit to a stock airmax AP and if you wanted to convert the AP to openwrt the performance tanks unbelievably for outdoor PtMP. easily a 30%+ loss. However, if you're wanting to get into 'wifi' at range this does work but you can't get very far because most wifi APs timings are too tight. On Wed, Mar 15, 2023 at 9:18 AM Dave Taht via LibreQoS < libreqos@lists.bufferbloat.net> wrote: > anybody still using these? > > ---------- Forwarded message --------- > From: Daniel González Cabanelas > Date: Wed, Mar 15, 2023 at 8:13 AM > Subject: [PATCH] ath79: Add support for Ubiquiti NanoBeam AC Gen2 XC > To: > > > The Ubiquiti NanoBeam AC Gen2 XC (NBE-5AC-Gen2) is an outdoor 802.11ac CPE > with a waterproof casing (ultrasonically welded) and bulb shaped. > > It's the same board as Gen1 but with a small antenna routed out of the SoC > and calibration data for this management radio in the "art" partition. > > Hardware: > SoC: Qualcomm Atheros QCA9558 > CPU: MIPS 74Kc V5.0 720 MHz, 1 core > RAM: 128 MB DDR2 > Flash: 16 MB SPI-NOR, MX25L12805D > Ethernet: 1x GbE > WiFi 5 GHz: Qualcomm Atheros QCA988X > WiFi 2.4 GHz: SoC (management radio) > Internal antenna 1: 19 dBi planar (5 GHz) > Internal antenna 2: 2 dBi PCB, connected via UFL (SoC) > Buttons: 1x reset > LEDs: 1x power, 1x Ethernet, 4x RSSI, all blue > PSU: 24 Vdc passive PoE > > Installation from stock airOS firmware: > - Follow instructions for XC-type Ubiquiti devices on OpenWrt wiki at > https://openwrt.org/toh/ubiquiti/common > > Back to stock firmware: > - Follow instructions for Ubiquiti recovery via TFTP at OpenWrt wiki. > > Signed-off-by: Daniel González Cabanelas > --- > .../dts/qca9558_ubnt_nanobeam-ac-gen2-xc.dts | 17 +++ > .../ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dts | 105 +---------------- > .../dts/qca9558_ubnt_nanobeam-ac-xc.dtsi | 107 ++++++++++++++++++ > .../generic/base-files/etc/board.d/01_leds | 1 + > .../generic/base-files/etc/board.d/02_network | 2 + > .../etc/hotplug.d/firmware/11-ath10k-caldata | 1 + > target/linux/ath79/image/generic-ubnt.mk | 10 ++ > 7 files changed, 141 insertions(+), 102 deletions(-) > create mode 100644 > target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-gen2-xc.dts > create mode 100644 target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dtsi > > diff --git a/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-gen2-xc.dts > b/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-gen2-xc.dts > new file mode 100644 > index 0000000000..629b5bfe0a > --- /dev/null > +++ b/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-gen2-xc.dts > @@ -0,0 +1,17 @@ > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT > +/* > + * Device Tree file for Ubiquiti Nanobeam NBE-5AC-Gen2 (XC) > + */ > + > +#include "qca9558_ubnt_nanobeam-ac-xc.dtsi" > + > +/ { > + compatible = "ubnt,nanobeam-ac-gen2-xc", "ubnt,xc", "qca,qca9558"; > + model = "Ubiquiti NanoBeam AC Gen2 (XC)"; > +}; > + > +&wmac { > + status = "okay"; > + > + mtd-cal-data = <&art 0x1000>; > +}; > diff --git a/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dts > b/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dts > index 91675ff615..898c249154 100644 > --- a/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dts > +++ b/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dts > @@ -1,110 +1,11 @@ > -// SPDX-License-Identifier: GPL-2.0-only > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT > /* > * Device Tree file for Ubiquiti Nanobeam NBE-5AC-19 (XC) > - * > - * Copyright (C) 2022 Daniel González Cabanelas > - * based on device tree from qca9558_ubnt_powerbeam-5ac-500.dts > */ > - > -#include "qca955x_ubnt_xc.dtsi" > + > +#include "qca9558_ubnt_nanobeam-ac-xc.dtsi" > > / { > compatible = "ubnt,nanobeam-ac-xc", "ubnt,xc", "qca,qca9558"; > model = "Ubiquiti NanoBeam AC Gen1 (XC)"; > - > - aliases { > - led-boot = &led_power; > - led-failsafe = &led_power; > - led-running = &led_power; > - led-upgrade = &led_power; > - }; > - > - keys { > - compatible = "gpio-keys"; > - > - reset { > - label = "Reset button"; > - linux,code = ; > - gpios = <&gpio 19 GPIO_ACTIVE_LOW>; > - debounce-interval = <60>; > - }; > - }; > - > - led_spi { > - compatible = "spi-gpio"; > - #address-cells = <1>; > - #size-cells = <0>; > - > - sck-gpios = <&gpio 0 GPIO_ACTIVE_HIGH>; > - mosi-gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; > - cs-gpios = <&gpio 3 GPIO_ACTIVE_HIGH>; > - num-chipselects = <1>; > - > - led_gpio: led_gpio@0 { > - compatible = "fairchild,74hc595"; > - reg = <0>; > - gpio-controller; > - #gpio-cells = <2>; > - registers-number = <1>; > - spi-max-frequency = <10000000>; > - enable-gpios = <&gpio 18 GPIO_ACTIVE_LOW>; > - }; > - }; > - > - leds { > - compatible = "gpio-leds"; > - > - rssi0 { > - label = "blue:rssi0"; > - gpios = <&led_gpio 0 GPIO_ACTIVE_LOW>; > - }; > - rssi1 { > - label = "blue:rssi1"; > - gpios = <&led_gpio 1 GPIO_ACTIVE_LOW>; > - }; > - rssi2 { > - label = "blue:rssi2"; > - gpios = <&led_gpio 2 GPIO_ACTIVE_LOW>; > - }; > - rssi3 { > - label = "blue:rssi3"; > - gpios = <&led_gpio 3 GPIO_ACTIVE_LOW>; > - }; > - led_power: power { > - label = "blue:power"; > - gpios = <&led_gpio 4 GPIO_ACTIVE_LOW>; > - default-state = "on"; > - }; > - }; > -}; > - > -&mdio0 { > - status = "okay"; > - > - phy4: ethernet-phy@4 { > - phy-mode = "sgmii"; > - reg = <4>; > - at803x-override-sgmii-link-check; > - }; > -}; > - > -ð0 { > - status = "okay"; > - > - pll-reg = <0 0x48 0>; > - pll-data = <0x03000000 0x00000101 0x00001313>; > - nvmem-cells = <&macaddr_art_0>; > - nvmem-cell-names = "mac-address"; > - phy-mode = "sgmii"; > - phy-handle = <&phy4>; > -}; > - > -&art { > - compatible = "nvmem-cells"; > - #address-cells = <1>; > - #size-cells = <1>; > - > - macaddr_art_0: macaddr@0 { > - reg = <0x0 0x6>; > - }; > }; > diff --git a/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dtsi > b/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dtsi > new file mode 100644 > index 0000000000..e68ceb7f5c > --- /dev/null > +++ b/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dtsi > @@ -0,0 +1,107 @@ > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT > +/* > + * Device Tree file for Ubiquiti Nanobeam XC > + * > + * Copyright (C) 2022 Daniel González Cabanelas > + * based on device tree from qca9558_ubnt_powerbeam-5ac-500.dts > + */ > + > +#include "qca955x_ubnt_xc.dtsi" > + > +/ { > + aliases { > + led-boot = &led_power; > + led-failsafe = &led_power; > + led-running = &led_power; > + led-upgrade = &led_power; > + }; > + > + keys { > + compatible = "gpio-keys"; > + > + reset { > + label = "Reset button"; > + linux,code = ; > + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; > + debounce-interval = <60>; > + }; > + }; > + > + led_spi { > + compatible = "spi-gpio"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + sck-gpios = <&gpio 0 GPIO_ACTIVE_HIGH>; > + mosi-gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; > + cs-gpios = <&gpio 3 GPIO_ACTIVE_LOW>; > + num-chipselects = <1>; > + > + led_gpio: led_gpio@0 { > + compatible = "fairchild,74hc595"; > + reg = <0>; > + gpio-controller; > + #gpio-cells = <2>; > + registers-number = <1>; > + spi-max-frequency = <10000000>; > + enable-gpios = <&gpio 18 GPIO_ACTIVE_LOW>; > + }; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + rssi0 { > + label = "blue:rssi0"; > + gpios = <&led_gpio 0 GPIO_ACTIVE_LOW>; > + }; > + rssi1 { > + label = "blue:rssi1"; > + gpios = <&led_gpio 1 GPIO_ACTIVE_LOW>; > + }; > + rssi2 { > + label = "blue:rssi2"; > + gpios = <&led_gpio 2 GPIO_ACTIVE_LOW>; > + }; > + rssi3 { > + label = "blue:rssi3"; > + gpios = <&led_gpio 3 GPIO_ACTIVE_LOW>; > + }; > + led_power: power { > + label = "blue:power"; > + gpios = <&led_gpio 4 GPIO_ACTIVE_LOW>; > + default-state = "on"; > + }; > + }; > +}; > + > +&mdio0 { > + status = "okay"; > + > + phy4: ethernet-phy@4 { > + phy-mode = "sgmii"; > + reg = <4>; > + at803x-override-sgmii-link-check; > + }; > +}; > + > +ð0 { > + status = "okay"; > + > + pll-reg = <0 0x48 0>; > + pll-data = <0x03000000 0x00000101 0x00001313>; > + nvmem-cells = <&macaddr_art_0>; > + nvmem-cell-names = "mac-address"; > + phy-mode = "sgmii"; > + phy-handle = <&phy4>; > +}; > + > +&art { > + compatible = "nvmem-cells"; > + #address-cells = <1>; > + #size-cells = <1>; > + > + macaddr_art_0: macaddr@0 { > + reg = <0x0 0x6>; > + }; > +}; > diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds > b/target/linux/ath79/generic/base-files/etc/board.d/01_leds > index 5855d2a928..a91e82f5e6 100644 > --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds > +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds > @@ -464,6 +464,7 @@ ubnt,bullet-ac|\ > ubnt,nanobeam-ac|\ > ubnt,nanobeam-ac-gen2|\ > ubnt,nanobeam-ac-xc|\ > +ubnt,nanobeam-ac-gen2-xc|\ > ubnt,nanostation-ac|\ > ubnt,powerbeam-5ac-gen2) > ucidef_set_rssimon "wlan0" "200000" "1" > diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network > b/target/linux/ath79/generic/base-files/etc/board.d/02_network > index b20a3c13f8..f5137385c2 100644 > --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network > +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network > @@ -101,6 +101,7 @@ ath79_setup_interfaces() > ubnt,litebeam-ac-gen2|\ > ubnt,nanobeam-ac|\ > ubnt,nanobeam-ac-xc|\ > + ubnt,nanobeam-ac-gen2-xc|\ > ubnt,nanostation-ac-loco|\ > ubnt,nanostation-loco-m-xw|\ > ubnt,powerbeam-5ac-500|\ > @@ -774,6 +775,7 @@ ath79_setup_macs() > ubnt,litebeam-ac-gen2|\ > ubnt,nanobeam-ac-gen2|\ > ubnt,nanobeam-ac-xc|\ > + ubnt,nanobeam-ac-gen2-xc|\ > ubnt,powerbeam-5ac-500|\ > ubnt,powerbeam-5ac-gen2) > label_mac=$(mtd_get_mac_binary art 0x5006) > diff --git > a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata > > b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata > index 4db311fde0..a79781237b 100644 > --- > a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata > +++ > b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata > @@ -45,6 +45,7 @@ case "$FIRMWARE" in > ubnt,nanobeam-ac|\ > ubnt,nanobeam-ac-gen2|\ > ubnt,nanobeam-ac-xc|\ > + ubnt,nanobeam-ac-gen2-xc|\ > ubnt,nanostation-ac|\ > ubnt,nanostation-ac-loco|\ > ubnt,powerbeam-5ac-500|\ > diff --git a/target/linux/ath79/image/generic-ubnt.mk > b/target/linux/ath79/image/generic-ubnt.mk > index 0f70649d03..a78ccaef82 100644 > --- a/target/linux/ath79/image/generic-ubnt.mk > +++ b/target/linux/ath79/image/generic-ubnt.mk > @@ -87,6 +87,16 @@ define Device/ubnt_nanobeam-ac-xc > endef > TARGET_DEVICES += ubnt_nanobeam-ac-xc > > +define Device/ubnt_nanobeam-ac-gen2-xc > + $(Device/ubnt-xc) > + SOC := qca9558 > + DEVICE_MODEL := NanoBeam AC > + DEVICE_VARIANT := Gen2 (XC) > + SUPPORTED_DEVICES += ubnt,nanobeam-ac-xc > + DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct rssileds > +endef > +TARGET_DEVICES += ubnt_nanobeam-ac-gen2-xc > + > define Device/ubnt_nanobeam-m5-xw > $(Device/ubnt-xw) > DEVICE_MODEL := NanoBeam M5 > -- > 2.39.2 > > > > > > _______________________________________________ > openwrt-devel mailing list > openwrt-devel@lists.openwrt.org > https://lists.openwrt.org/mailman/listinfo/openwrt-devel > > > -- > Come Heckle Mar 6-9 at: https://www.understandinglatency.com/ > Dave Täht CEO, TekLibre, LLC > _______________________________________________ > LibreQoS mailing list > LibreQoS@lists.bufferbloat.net > https://lists.bufferbloat.net/listinfo/libreqos >