* Re: [LibreQoS] Fwd: [PATCH] ath79: Add support for Ubiquiti NanoBeam AC Gen2 XC
2023-03-15 15:17 ` [LibreQoS] Fwd: [PATCH] ath79: Add support for Ubiquiti NanoBeam AC Gen2 XC Dave Taht
@ 2023-03-15 15:22 ` dan
0 siblings, 0 replies; 2+ messages in thread
From: dan @ 2023-03-15 15:22 UTC (permalink / raw)
To: Dave Taht; +Cc: libreqos
[-- Attachment #1: Type: text/plain, Size: 14588 bytes --]
Yes, but you can't connect an openwrt flashed unit to a stock airmax AP and
if you wanted to convert the AP to openwrt the performance tanks
unbelievably for outdoor PtMP. easily a 30%+ loss. However, if you're
wanting to get into 'wifi' at range this does work but you can't get very
far because most wifi APs timings are too tight.
On Wed, Mar 15, 2023 at 9:18 AM Dave Taht via LibreQoS <
libreqos@lists.bufferbloat.net> wrote:
> anybody still using these?
>
> ---------- Forwarded message ---------
> From: Daniel González Cabanelas <dgcbueu@gmail.com>
> Date: Wed, Mar 15, 2023 at 8:13 AM
> Subject: [PATCH] ath79: Add support for Ubiquiti NanoBeam AC Gen2 XC
> To: <openwrt-devel@lists.openwrt.org>
>
>
> The Ubiquiti NanoBeam AC Gen2 XC (NBE-5AC-Gen2) is an outdoor 802.11ac CPE
> with a waterproof casing (ultrasonically welded) and bulb shaped.
>
> It's the same board as Gen1 but with a small antenna routed out of the SoC
> and calibration data for this management radio in the "art" partition.
>
> Hardware:
> SoC: Qualcomm Atheros QCA9558
> CPU: MIPS 74Kc V5.0 720 MHz, 1 core
> RAM: 128 MB DDR2
> Flash: 16 MB SPI-NOR, MX25L12805D
> Ethernet: 1x GbE
> WiFi 5 GHz: Qualcomm Atheros QCA988X
> WiFi 2.4 GHz: SoC (management radio)
> Internal antenna 1: 19 dBi planar (5 GHz)
> Internal antenna 2: 2 dBi PCB, connected via UFL (SoC)
> Buttons: 1x reset
> LEDs: 1x power, 1x Ethernet, 4x RSSI, all blue
> PSU: 24 Vdc passive PoE
>
> Installation from stock airOS firmware:
> - Follow instructions for XC-type Ubiquiti devices on OpenWrt wiki at
> https://openwrt.org/toh/ubiquiti/common
>
> Back to stock firmware:
> - Follow instructions for Ubiquiti recovery via TFTP at OpenWrt wiki.
>
> Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
> ---
> .../dts/qca9558_ubnt_nanobeam-ac-gen2-xc.dts | 17 +++
> .../ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dts | 105 +----------------
> .../dts/qca9558_ubnt_nanobeam-ac-xc.dtsi | 107 ++++++++++++++++++
> .../generic/base-files/etc/board.d/01_leds | 1 +
> .../generic/base-files/etc/board.d/02_network | 2 +
> .../etc/hotplug.d/firmware/11-ath10k-caldata | 1 +
> target/linux/ath79/image/generic-ubnt.mk | 10 ++
> 7 files changed, 141 insertions(+), 102 deletions(-)
> create mode 100644
> target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-gen2-xc.dts
> create mode 100644 target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dtsi
>
> diff --git a/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-gen2-xc.dts
> b/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-gen2-xc.dts
> new file mode 100644
> index 0000000000..629b5bfe0a
> --- /dev/null
> +++ b/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-gen2-xc.dts
> @@ -0,0 +1,17 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/*
> + * Device Tree file for Ubiquiti Nanobeam NBE-5AC-Gen2 (XC)
> + */
> +
> +#include "qca9558_ubnt_nanobeam-ac-xc.dtsi"
> +
> +/ {
> + compatible = "ubnt,nanobeam-ac-gen2-xc", "ubnt,xc", "qca,qca9558";
> + model = "Ubiquiti NanoBeam AC Gen2 (XC)";
> +};
> +
> +&wmac {
> + status = "okay";
> +
> + mtd-cal-data = <&art 0x1000>;
> +};
> diff --git a/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dts
> b/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dts
> index 91675ff615..898c249154 100644
> --- a/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dts
> +++ b/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dts
> @@ -1,110 +1,11 @@
> -// SPDX-License-Identifier: GPL-2.0-only
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> /*
> * Device Tree file for Ubiquiti Nanobeam NBE-5AC-19 (XC)
> - *
> - * Copyright (C) 2022 Daniel González Cabanelas <dgcbueu@gmail.com>
> - * based on device tree from qca9558_ubnt_powerbeam-5ac-500.dts
> */
> -
> -#include "qca955x_ubnt_xc.dtsi"
> +
> +#include "qca9558_ubnt_nanobeam-ac-xc.dtsi"
>
> / {
> compatible = "ubnt,nanobeam-ac-xc", "ubnt,xc", "qca,qca9558";
> model = "Ubiquiti NanoBeam AC Gen1 (XC)";
> -
> - aliases {
> - led-boot = &led_power;
> - led-failsafe = &led_power;
> - led-running = &led_power;
> - led-upgrade = &led_power;
> - };
> -
> - keys {
> - compatible = "gpio-keys";
> -
> - reset {
> - label = "Reset button";
> - linux,code = <KEY_RESTART>;
> - gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
> - debounce-interval = <60>;
> - };
> - };
> -
> - led_spi {
> - compatible = "spi-gpio";
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - sck-gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
> - mosi-gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
> - cs-gpios = <&gpio 3 GPIO_ACTIVE_HIGH>;
> - num-chipselects = <1>;
> -
> - led_gpio: led_gpio@0 {
> - compatible = "fairchild,74hc595";
> - reg = <0>;
> - gpio-controller;
> - #gpio-cells = <2>;
> - registers-number = <1>;
> - spi-max-frequency = <10000000>;
> - enable-gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
> - };
> - };
> -
> - leds {
> - compatible = "gpio-leds";
> -
> - rssi0 {
> - label = "blue:rssi0";
> - gpios = <&led_gpio 0 GPIO_ACTIVE_LOW>;
> - };
> - rssi1 {
> - label = "blue:rssi1";
> - gpios = <&led_gpio 1 GPIO_ACTIVE_LOW>;
> - };
> - rssi2 {
> - label = "blue:rssi2";
> - gpios = <&led_gpio 2 GPIO_ACTIVE_LOW>;
> - };
> - rssi3 {
> - label = "blue:rssi3";
> - gpios = <&led_gpio 3 GPIO_ACTIVE_LOW>;
> - };
> - led_power: power {
> - label = "blue:power";
> - gpios = <&led_gpio 4 GPIO_ACTIVE_LOW>;
> - default-state = "on";
> - };
> - };
> -};
> -
> -&mdio0 {
> - status = "okay";
> -
> - phy4: ethernet-phy@4 {
> - phy-mode = "sgmii";
> - reg = <4>;
> - at803x-override-sgmii-link-check;
> - };
> -};
> -
> -ð0 {
> - status = "okay";
> -
> - pll-reg = <0 0x48 0>;
> - pll-data = <0x03000000 0x00000101 0x00001313>;
> - nvmem-cells = <&macaddr_art_0>;
> - nvmem-cell-names = "mac-address";
> - phy-mode = "sgmii";
> - phy-handle = <&phy4>;
> -};
> -
> -&art {
> - compatible = "nvmem-cells";
> - #address-cells = <1>;
> - #size-cells = <1>;
> -
> - macaddr_art_0: macaddr@0 {
> - reg = <0x0 0x6>;
> - };
> };
> diff --git a/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dtsi
> b/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dtsi
> new file mode 100644
> index 0000000000..e68ceb7f5c
> --- /dev/null
> +++ b/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dtsi
> @@ -0,0 +1,107 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/*
> + * Device Tree file for Ubiquiti Nanobeam XC
> + *
> + * Copyright (C) 2022 Daniel González Cabanelas <dgcbueu@gmail.com>
> + * based on device tree from qca9558_ubnt_powerbeam-5ac-500.dts
> + */
> +
> +#include "qca955x_ubnt_xc.dtsi"
> +
> +/ {
> + aliases {
> + led-boot = &led_power;
> + led-failsafe = &led_power;
> + led-running = &led_power;
> + led-upgrade = &led_power;
> + };
> +
> + keys {
> + compatible = "gpio-keys";
> +
> + reset {
> + label = "Reset button";
> + linux,code = <KEY_RESTART>;
> + gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
> + debounce-interval = <60>;
> + };
> + };
> +
> + led_spi {
> + compatible = "spi-gpio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + sck-gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
> + mosi-gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
> + cs-gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
> + num-chipselects = <1>;
> +
> + led_gpio: led_gpio@0 {
> + compatible = "fairchild,74hc595";
> + reg = <0>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + registers-number = <1>;
> + spi-max-frequency = <10000000>;
> + enable-gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + rssi0 {
> + label = "blue:rssi0";
> + gpios = <&led_gpio 0 GPIO_ACTIVE_LOW>;
> + };
> + rssi1 {
> + label = "blue:rssi1";
> + gpios = <&led_gpio 1 GPIO_ACTIVE_LOW>;
> + };
> + rssi2 {
> + label = "blue:rssi2";
> + gpios = <&led_gpio 2 GPIO_ACTIVE_LOW>;
> + };
> + rssi3 {
> + label = "blue:rssi3";
> + gpios = <&led_gpio 3 GPIO_ACTIVE_LOW>;
> + };
> + led_power: power {
> + label = "blue:power";
> + gpios = <&led_gpio 4 GPIO_ACTIVE_LOW>;
> + default-state = "on";
> + };
> + };
> +};
> +
> +&mdio0 {
> + status = "okay";
> +
> + phy4: ethernet-phy@4 {
> + phy-mode = "sgmii";
> + reg = <4>;
> + at803x-override-sgmii-link-check;
> + };
> +};
> +
> +ð0 {
> + status = "okay";
> +
> + pll-reg = <0 0x48 0>;
> + pll-data = <0x03000000 0x00000101 0x00001313>;
> + nvmem-cells = <&macaddr_art_0>;
> + nvmem-cell-names = "mac-address";
> + phy-mode = "sgmii";
> + phy-handle = <&phy4>;
> +};
> +
> +&art {
> + compatible = "nvmem-cells";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + macaddr_art_0: macaddr@0 {
> + reg = <0x0 0x6>;
> + };
> +};
> diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
> b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
> index 5855d2a928..a91e82f5e6 100644
> --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
> +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
> @@ -464,6 +464,7 @@ ubnt,bullet-ac|\
> ubnt,nanobeam-ac|\
> ubnt,nanobeam-ac-gen2|\
> ubnt,nanobeam-ac-xc|\
> +ubnt,nanobeam-ac-gen2-xc|\
> ubnt,nanostation-ac|\
> ubnt,powerbeam-5ac-gen2)
> ucidef_set_rssimon "wlan0" "200000" "1"
> diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network
> b/target/linux/ath79/generic/base-files/etc/board.d/02_network
> index b20a3c13f8..f5137385c2 100644
> --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
> +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
> @@ -101,6 +101,7 @@ ath79_setup_interfaces()
> ubnt,litebeam-ac-gen2|\
> ubnt,nanobeam-ac|\
> ubnt,nanobeam-ac-xc|\
> + ubnt,nanobeam-ac-gen2-xc|\
> ubnt,nanostation-ac-loco|\
> ubnt,nanostation-loco-m-xw|\
> ubnt,powerbeam-5ac-500|\
> @@ -774,6 +775,7 @@ ath79_setup_macs()
> ubnt,litebeam-ac-gen2|\
> ubnt,nanobeam-ac-gen2|\
> ubnt,nanobeam-ac-xc|\
> + ubnt,nanobeam-ac-gen2-xc|\
> ubnt,powerbeam-5ac-500|\
> ubnt,powerbeam-5ac-gen2)
> label_mac=$(mtd_get_mac_binary art 0x5006)
> diff --git
> a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
>
> b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
> index 4db311fde0..a79781237b 100644
> ---
> a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
> +++
> b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
> @@ -45,6 +45,7 @@ case "$FIRMWARE" in
> ubnt,nanobeam-ac|\
> ubnt,nanobeam-ac-gen2|\
> ubnt,nanobeam-ac-xc|\
> + ubnt,nanobeam-ac-gen2-xc|\
> ubnt,nanostation-ac|\
> ubnt,nanostation-ac-loco|\
> ubnt,powerbeam-5ac-500|\
> diff --git a/target/linux/ath79/image/generic-ubnt.mk
> b/target/linux/ath79/image/generic-ubnt.mk
> index 0f70649d03..a78ccaef82 100644
> --- a/target/linux/ath79/image/generic-ubnt.mk
> +++ b/target/linux/ath79/image/generic-ubnt.mk
> @@ -87,6 +87,16 @@ define Device/ubnt_nanobeam-ac-xc
> endef
> TARGET_DEVICES += ubnt_nanobeam-ac-xc
>
> +define Device/ubnt_nanobeam-ac-gen2-xc
> + $(Device/ubnt-xc)
> + SOC := qca9558
> + DEVICE_MODEL := NanoBeam AC
> + DEVICE_VARIANT := Gen2 (XC)
> + SUPPORTED_DEVICES += ubnt,nanobeam-ac-xc
> + DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct rssileds
> +endef
> +TARGET_DEVICES += ubnt_nanobeam-ac-gen2-xc
> +
> define Device/ubnt_nanobeam-m5-xw
> $(Device/ubnt-xw)
> DEVICE_MODEL := NanoBeam M5
> --
> 2.39.2
>
>
>
>
>
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel@lists.openwrt.org
> https://lists.openwrt.org/mailman/listinfo/openwrt-devel
>
>
> --
> Come Heckle Mar 6-9 at: https://www.understandinglatency.com/
> Dave Täht CEO, TekLibre, LLC
> _______________________________________________
> LibreQoS mailing list
> LibreQoS@lists.bufferbloat.net
> https://lists.bufferbloat.net/listinfo/libreqos
>
[-- Attachment #2: Type: text/html, Size: 19350 bytes --]
^ permalink raw reply [flat|nested] 2+ messages in thread