[Cake] policer question

Wed May 27 15:35:37 EDT 2015

and in the end, that new modem crapped out completely

On Wed, May 27, 2015 at 10:12 AM, Dave Taht <dave.taht at gmail.com> wrote:
> On Tue, May 26, 2015 at 3:49 AM, Sebastian Moeller <moeller0 at gmx.de> wrote:
>> Hi Dave,
>>
>> I just stumbled over your last edit of "wondershaper needs to go the way of the dodo”; especially the following caught my attention (lines 303 - 311):
>>
>> ## The ingress policer doesn't work against ipv6, so if you have mixed traffic
>> ## you are not matching all of it, and the policer fails entirely
>> ## A correct, modern line for this would be:
>> ## tc filter add dev ${DEV} parent ffff: protocol all match u32 0 0 \
>> ## police rate ${DOWNLINK}kbit burst 100k drop flowid :1
>> ##
>> ## Even if it did work, the police burst size is too small for higher speed
>> ## connections and what I suggest above for a burst size needs to be
>> ## a calculated figure.(that one works ok at 100mbit)
>>
>> I think we should implement a policer setting in SQM (if only for testing) so I wonder how to set the burst size?
>> I think we basically can run the policer only X times per second, so we should allow something along the lines of:
>> bandwidth [bits/sec] / X [1/sec] = max bits in batch [bits]
>> Since in the end, we only can work in bursts/batches we need to figure out what worst-case batches to expect.
>> Now it would be sweet if we could get a handle on X, but what about just using the following approximation:
>>
>> How often does the policer run per second worst case?
>>
>> 100[kB]*1000*8 = 800000 [bit]
>> (100*1000^2 [bit/sec] / (100*1000*8) [bit]) = 125 1/sec or 8 milliseconds per invocation
>>
>> So your example seems to show that if we can run 125 times per second we will be able to drain enough packets so we do not drop excessively many packets. This bursting issue will increase the latency under load for sure, but I guess not more than 8ms on average?.
>>         Now, I guess one issue will be that this is not simply dependent on either data size or packet count, but probably we are both limited at how many packets per second we can process as well as how many bytes. So what about:
>>
>> burst = (bandwidth [bits/sec] /  125 [1/sec]) / (1000*8) [kB]
>>
>> This is probably too simplistic, but better than nothing.
>>
>> I would appreciate any hints how to improve this; so thanks in advance. Now all I need to do is hook this up with sqm-scripts and then go test the hell out of it ;)
>>
>> Best Regards
>>         Sebastian
>
> Well, I am pretty sure policing as currently understood is generally
> not a win compared to inbound shaping with aqm, particularly in the
> concatenated queues case which was the one I wanted to address (90/100
> rate differential).
>
> policers have generally been "pitched" as a means of customer
> bandwidth control (with CIR and other "features"), and do seem to be
> highly used...
>
> What I wanted to do was come up with a kinder, gentler policer that
> was effective but less damaging to non-tcp-like flow types, and the
> whole concept of a burst parameter just doesn't work with shorter RTTs
> in particular when used with ewma. The initial burst characteristics
> we see today are very different from the slow speeds and small initial
> windows (2) of yesteryear, and we tend to see a bunch of flows in slow
> start all at the same time. signal sent is too late to dissipate the
> original burst, and yet the policer signal is a brick wall so once it
> kicks in bad things happen to all flows.
>
> So, for example, I came up with a simple mod to the existing policer
> code, to "shred" inbound with a fq-like idea The shred.patch and some
> flent data are here:
>
> http://snapon.lab.bufferbloat.net/~cero3/bobbie/
>
> But: new data points galore hit me at the same time.
>
> Recently I boosted my signal strength on my cable modems in the
> biggest testbed, and switched to a new one. the old one, latched up at
> 110mbit down prior (and really horrible download bufferbloat), started
> giving me 172mbit service. This morning I measured that at about
> 142mbit service. THAT difference in performance ended up pretty
> dramatic, I went from where dslreports would peak at seconds on
> inbound to mere 100s of ms on an unshaped modem.
>
> http://www.dslreports.com/speedtest/560968
>
> dslreports changed their cable test to be 16 down and 12 up, also (from 16/6).
>
> ( I have also made so many other changes to the test driving box - for
> example I reduced tcp_limit_output_bytes to 4k and started using the
> sch_fq qdisc on my test driver box - and certainly it is my hope that
> the cable isps sat up and took notice and deployed some fixes in the
> past few weeks)
>
> So here is me just fixing outbound on this test:
>
> http://www.dslreports.com/speedtest/560989
>
> so there are WAY too many variables in play again.
>
> and trying to fix inbound (and failing)
>
> http://www.dslreports.com/speedtest/561097
>
> (and see the dataset)
>
> I am still seeing 30ms of induced latency on the rrul test but it is
> so far from horrible that I think I am still dreaming.
> and i have a whole bunch of variables to tediously recheck.
>
>>
>>
>>
>>
>
>
>
> --
> Dave Täht
> Open Networking needs **Open Source Hardware**
>
> https://plus.google.com/u/0/+EricRaymond/posts/JqxCe2pFr67


-- 
Dave Täht
What will it take to vastly improve wifi for everyone?
https://plus.google.com/u/0/explore/makewififast