[Rpm] [ippm] Preliminary measurement comparison of "Working Latency" metrics
Dave Taht
dave.taht at gmail.com
Mon Oct 31 12:52:04 EDT 2022
Thank you very much for the steer to RFC9097. I'd completely missed that.
On Mon, Oct 31, 2022 at 9:04 AM MORTON JR., AL <acmorton at att.com> wrote:
>
> (astute readers may have guessed that I pressed "send" too soon on previous message...)
>
> I also conducted upstream tests this time, here are the results:
> (capacity in Mbps, delays in ms, h and m are RPM categories, High and Medium)
>
> Net Qual UDPST (RFC9097) Ookla
> UpCap RPM DelLD DelMin UpCap RTTmin RTTrange UpCap Ping(no load)
> 34 1821 h 33ms 11ms 23 (42) 28 0-252 22 8
> 22 281 m 214ms 8ms 27 (52) 25 5-248 22 8
> 22 290 m 207ms 8ms 27 (55) 28 0-253 22 9
> 21 330 m 182ms 11ms 23 (44) 28 0-255 22 7
> 22 334 m 180ms 9ms 33 (56) 25 0-255 22 9
>
> The Upstream capacity measurements reflect an interesting feature that we can reliably and repeatably measure with UDPST. The first ~3 seconds of upstream data experience a "turbo mode" of ~50Mbps. UDPST displays this behavior in its 1 second sub-interval measurements and has a bimodal reporting option that divides the complete measurement interval in two time intervals to report an initial (turbo) max capacity and a steady-state max capacity for the later intervals. The UDPST capacity results present both measurements: steady-state first.
Certainly we can expect bi-model distributions from many ISPs, as, for
one thing, the "speedboost" concept remains popular, except that it's
misnamed, as it should be called speed-subtract or speed-lose. Worse,
it is often configured "sneakily", in that it doesn't kick in for the
typical observed duration of the test, for some, they cut the
available bandwidth about 20s in, others, 1 or 5 minutes.
One of my biggest issues with the rpm spec so far is that it should,
at least, sometimes, run randomly longer than the overly short
interval it runs for and the tools also allow for manual override of length.
we caught a lot of tomfoolery with flent's rrul test running by default for 1m.
Also, AQMs on the path can take a while to find the optimal drop or mark rate.
>
> The capacity processing in networkQuality and Ookla appear to report the steady-state result.
Ookla used to basically report the last result. Also it's not a good
indicator of web traffic behavior at all, watching the curve
go up much more slowly in their test on say, fiber 2ms, vs starlink, (40ms)....
So adding another mode - how quickly is peak bandwidth actually
reached, would be nice.
I haven't poked into the current iteration of the goresponsiveness
test at all: https://github.com/network-quality/goresponsiveness it
would be good to try collecting more statistics and histograms and
methods of analyzing the data in that libre-source version.
How does networkQuality compare vs a vs your tool vs a vs goresponsiveness?
>I watched the upstream capacity measurements on the Ookla app, and could easily see the initial rise to 40-50Mbps, then the drop to ~22Mbps for most of the test which determined the final result.
I tend to get upset when I see ookla's new test flash a peak result in
the seconds and then settle on some lower number somehow.
So far as I know they are only sampling the latency every 250ms.
>
> The working latency is about 200ms in networkQuality and about 280ms as measured by UDPST (RFC9097). Note that the networkQuality minimum delay is ~20ms lower than the UDPST RTTmin, so this accounts for some of the difference in working latency. Also, we used the very dynamic Type C load adjustment/search algorithm in UDPST during all of this testing, which could explain the higher working latency to some degree.
>
> So, it's worth noting that the measurements needed for assessing working latency/responsiveness are available in the UDPST utility, and that the UDPST measurements are conducted on UDP transport (used by a growing fraction of Internet traffic).
Thx, didn't know of this work til now!
have you tried irtt?
>
> comments welcome of course,
> Al
>
> > -----Original Message-----
> > From: ippm <ippm-bounces at ietf.org> On Behalf Of MORTON JR., AL
> > Sent: Sunday, October 30, 2022 8:09 PM
> > To: ippm at ietf.org
> > Subject: Re: [ippm] Preliminary measurement comparison of "Working Latency"
> > metrics
> >
> >
> > Hi again RPM friends and IPPM'ers,
> >
> > As promised, I repeated the tests shared last week, this time using both the
> > verbose (-v) and sequential (-s) dwn/up test options of networkQuality. I
> > followed Sebastian's calculations as well.
> >
> > Working Latency & Capacity Summary
> >
> > Net Qual UDPST Ookla
> > DnCap RPM DelLD DelMin DnCap RTTmin RTTrange DnCap
> > Ping(no load)
> > 885 916 m 66ms 8ms 970 28 0-20 940 8
> > 888 1355 h 44ms 8ms 966 28 0-23 940 8
> > 891 1109 h 54ms 8ms 968 27 0-19 940 9
> > 887 1141 h 53ms 11ms 966 27 0-18 937 7
> > 884 1151 h 52ms 9ms 968 28 0-20 937 9
> >
> > With the sequential test option, I noticed that networkQuality achieved nearly
> > the maximum capacity reported almost immediately at the start of a test.
> > However, the reported capacities are low by about 60Mbps, especially when
> > compared to the Ookla TCP measurements.
> >
> > The loaded delay (DelLD) is similar to the UDPST RTTmin + (the high end of the
> > RTTrange), for example 54ms compared to (27+19=46). Most of the networkQuality
> > RPM measurements were categorized as "High". There doesn't seem to be much
> > buffering in the downstream direction.
> >
> >
> >
> > > -----Original Message-----
> > > From: ippm <ippm-bounces at ietf.org> On Behalf Of MORTON JR., AL
> > > Sent: Monday, October 24, 2022 6:36 PM
> > > To: ippm at ietf.org
> > > Subject: [ippm] Preliminary measurement comparison of "Working Latency"
> > > metrics
> > >
> > >
> > > Hi RPM friends and IPPM'ers,
> > >
> > > I was wondering what a comparison of some of the "working latency" metrics
> > > would look like, so I ran some tests using a service on DOCSIS 3.1, with the
> > > downlink provisioned for 1Gbps.
> > >
> > > I intended to run apple's networkQuality, UDPST (RFC9097), and Ookla
> > Speedtest
> > > with as similar connectivity as possible (but we know that the traffic will
> > > diverge to different servers and we can't change that aspect).
> > >
> > > Here's a quick summary of yesterday's results:
> > >
> > > Working Latency & Capacity Summary
> > >
> > > Net Qual UDPST Ookla
> > > DnCap RPM DnCap RTTmin RTTVarRnge DnCap Ping(no load)
> > > 878 62 970 28 0-19 941 6
> > > 891 92 970 27 0-20 940 7
> > > 891 120 966 28 0-22 937 9
> > > 890 112 970 28 0-21 940 8
> > > 903 70 970 28 0-16 935 9
> > >
> > > Note: all RPM values were categorized as Low.
> > >
> > > networkQuality downstream capacities are always on the low side compared to
> > > others. We would expect about 940Mbps for TCP, and that's mostly what Ookla
> > > achieved. I think that a longer test duration might be needed to achieve the
> > > actual 1Gbps capacity with networkQuality; intermediate values observed were
> > > certainly headed in the right direction. (I recently upgraded to Monterey
> > 12.6
> > > on my MacBook, so should have the latest version.)
> > >
> > > Also, as Sebastian Moeller's message to the list reminded me, I should have
> > > run the tests with the -v option to help with comparisons. I'll repeat this
> > > test when I can make time.
> > >
> > > The UDPST measurements of RTTmin (minimum RTT observed during the test) and
> > > the range of variation above the minimum (RTTVarRnge) add-up to very
> > > reasonable responsiveness IMO, so I'm not clear why RPM graded this access
> > and
> > > path as "Low". The UDPST server I'm using is in NJ, and I'm in Chicago
> > > conducting tests, so the minimum 28ms is typical. UDPST measurements were
> > run
> > > on an Ubuntu VM in my MacBook.
> > >
> > > The big disappointment was that the Ookla desktop app I updated over the
> > > weekend did not include the new responsiveness metric! I included the ping
> > > results anyway, and it was clearly using a server in the nearby area.
> > >
> > > So, I have some more work to do, but I hope this is interesting-enough to
> > > start some comparison discussions, and bring-out some suggestions.
> > >
> > > happy testing all,
> > > Al
> > >
> > >
> > >
> > >
> > > _______________________________________________
> > > ippm mailing list
> > > ippm at ietf.org
> > >
> > https://urldefense.com/v3/__https://www.ietf.org/mailman/listinfo/ippm__;!!Bhd
> > >
> > T!hd5MvMQw5eiICQbsfoNaZBUS38yP4YIodBvz1kV5VsX_cGIugVnz5iIkNqi6fRfIQzWef_xKqg4$
> >
> > _______________________________________________
> > ippm mailing list
> > ippm at ietf.org
> > https://urldefense.com/v3/__https://www.ietf.org/mailman/listinfo/ippm__;!!Bhd
> > T!g-FsktB_l9MMSGNUge6FXDkL1npaKtKcyDtWLcTZGpCunxNNCcTImH8YjC9eUT262Wd8q1EBpiw$
>
> _______________________________________________
> ippm mailing list
> ippm at ietf.org
> https://www.ietf.org/mailman/listinfo/ippm
--
This song goes out to all the folk that thought Stadia would work:
https://www.linkedin.com/posts/dtaht_the-mushroom-song-activity-6981366665607352320-FXtz
Dave Täht CEO, TekLibre, LLC
More information about the Rpm
mailing list